Looking for:
ULTIMAKER 3 ORIGINAL MANUAL Pdf Download | ManualsLib
Page 42 Clean the nozzles While using the Ultimaker 3, material can get stuck to the nozzles. Don’t have an account?
Clean feeder ultimaker 3 free download.Hi, how can we help?
Ultimaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. You can withdraw your consent at any time. You can find more information about cookies on our Privacy and Cookie Policy page. For the best print results it is important to keep the Ultimaker 3 clean while using it. Therefore it is advised not to use the Ultimaker 3 in a room where it can easily be covered with dust and to remove small pieces of material that might be in the printer.
Besides this, there are a few parts in the Ultimaker 3 that might require more regular cleaning. After printing, there might be excess glue stuck to the glass plate. This can cause an uneven print surface. Removing a print may also reduce the adhesion quality of a layer of glue, so it is advised to regularly clean the glass plate and reapply glue.
Before starting a new print, always check the surface of the glass plate. At least once a month, clean the plate thoroughly by taking the following steps:. Note: Always make sure that the Ultimaker 3 is turned off and build plate has cooled down. Caution : Leaving the build plate clamps open may damage your Ultimaker 3 when the build plate is raised.
While using the Ultimaker 3, material can get stuck to the nozzles. Although this will not damage your printer, it is recommended keep the nozzles clean in order to achieve the best print results. Before starting a new print, always check the nozzles. At least once a month, remove the plastic from the outside of the nozzles by taking the following steps:. Caution : Do not touch the nozzles and be careful while cleaning it as they will become hot. After many hours of printing, or when material has been ground down, small filament particles can build up in the feeder.
These can end up in the Bowden tubes or print cores, which can impact print quality. Clean the feeders and Bowden tubes at least once a month, or after experiencing an issue with filament grinding. Particles in the Bowden tubes can impede smooth movement of the filament or mix colors. To clean them, the Bowden tubes have to be removed from the printer. Small pieces of material can gather inside the printer, such as priming blobs. Remove these from the inside of the printer with a cloth or vacuum cleaner.
Pay extra attention to the area around the Z limit switch as obstructions here can cause print problems. Caution: Leaving larger objects on the bottom panel can lead to errors, as they prevent the build plate from homing properly. I agree, continue browsing Refuse. Clean the glass plate After printing, there might be excess glue stuck to the glass plate. At least once a month, clean the plate thoroughly by taking the following steps: Note: Always make sure that the Ultimaker 3 is turned off and build plate has cooled down.
Manually place the build plate at the bottom of the Ultimaker 3 Open the build plate clamps at the front, slide the glass plate forward and take it out of the printer Use lukewarm water and a sponge to remove the layer of glue.
If necessary, some soap or detergent can also be used Dry the glass plate with a clean cloth Place the glass plate on the heated bed with the warning sticker facing upwards. Ensure that it snaps into the build plate clamps at the back, and close the build plate clamps at the front side to secure it Caution : Leaving the build plate clamps open may damage your Ultimaker 3 when the build plate is raised.
Clean the nozzles While using the Ultimaker 3, material can get stuck to the nozzles. Repeat this for print core 2 and make sure this print core is lowered Wait for the plastic on the outside to get soft. When the nozzles are hot, carefully remove the material with tweezers Caution : Do not touch the nozzles and be careful while cleaning it as they will become hot.
Comments 0 comments. Articles in this section Update the Ultimaker 3 firmware Ultimaker 3 firmware release notes Replace the build plate clamps of the Ultimaker 3 Replace the radial fans of the Ultimaker 3 Replace the axial fan of the Ultimaker 3 Replace the tube coupling collet of the Ultimaker 3 Replace the clamp clip of the Ultimaker 3 Replace the Bowden tubes on the Ultimaker 3 Clean the feeders on the Ultimaker 3 Lubricate the lead screw of the Z motor on the Ultimaker 3 See more.
Cleaning the Ultimaker 3 – Ultimaker Support.ULTIMAKER 3 INSTALLATION AND USER MANUAL Pdf Download | ManualsLib
The feeders forward filament to the print head. To make sure that exactly the right amount of material is extruded, it is important that the feeder gears can turn smoothly. After many hours of printing, or when the material has been ground down, there is a chance that there are small filament particles in the feeders. It is recommended to clean the inside of the feeders after three months. In order to do this, the feeders have to be removed from the printer.
Tip: Be careful not to lose the ring that is located at the bottom of the feeder. If it falls out, place it back in the feeder housing with the widest side at the top. You can withdraw your consent at any time. You can find more information about cookies on our Privacy and Cookie Policy page. The feeders forward filament to the print head. To make sure that exactly the right amount of material is extruded, it is important that the feeder gears can turn smoothly.
After many hours of printing, or when material has been ground down, there is a chance that there are small filament particles in the feeders. In addition to blowing out the particles once a month, it is recommended to also clean the inside of the feeders after one year of printing. Small pieces of material can gather inside the printer, such as priming blobs. Remove these from the inside of the printer with a cloth or vacuum cleaner.
Pay extra attention to the area around the Z limit switch as obstructions here can cause print problems. Caution: Leaving larger objects on the bottom panel can lead to errors, as they prevent the build plate from homing properly. I agree, continue browsing Refuse. Clean the glass plate After printing, there might be excess glue stuck to the glass plate. At least once a month, clean the plate thoroughly by taking the following steps: Note: Always make sure that the Ultimaker 3 is turned off and build plate has cooled down.
Manually place the build plate at the bottom of the Ultimaker 3 Open the build plate clamps at the front, slide the glass plate forward and take it out of the printer Use lukewarm water and a sponge to remove the layer of glue.
If necessary, some soap or detergent can also be used Dry the glass plate with a clean cloth Place the glass plate on the heated bed with the warning sticker facing upwards. Ensure that it snaps into the build plate clamps at the back, and close the build plate clamps at the front side to secure it Caution : Leaving the build plate clamps open may damage your Ultimaker 3 when the build plate is raised.
Clean the nozzles While using the Ultimaker 3, material can get stuck to the nozzles. Repeat this for print core 2 and make sure this print core is lowered Wait for the plastic on the outside to get soft.
When the nozzles are hot, carefully remove the material with tweezers Caution : Do not touch the nozzles and be careful while cleaning it as they will become hot.